How to Make a Sex Doll?

There are a lot of silicone sex dolls in the market. As ordinary consumers, we are not sure whether they are made of platinum silicone? Therefore, in order to ensure the high quality of silicone sex dolls, you can actually DIY sex silicone dolls yourself. The silicone sex doll made in this way will be safer and cheaper. But it takes a lot of time.

Prepare materials

Tools: utility knife, dye pen, needle and thread, electric wind, gauze.

Release agent: Vaseline.

Auxiliary: silicone glue, cosmetic contact lenses, artificial eyelashes, wigs, nail art

The production process of the first part of the sex doll

Step 1: Use sludge to make parting line, and make a circle around the model

Tip: You can use ordinary sludge or refined sludge. Carved sludge can be wrapped in clinker tape, softened in hot water, and taken out for use. It can also be softened with electric wind. The outer circle of ocher is the boundary of the model. After making one side of the model, make the other side, so that we can easily install and disassemble it when we inject platinum silica gel later.

Step 2: Mix the platinum silica gel with high viscosity in a ratio of 1:1 and stir.

Step 3: Apply a layer of petroleum jelly on the top half of the face model with the sludge, and then apply a layer of mixed platinum silica gel.

Step 4: After the platinum silica gel has solidified, make a layer of plaster or resin outer mold. (If you use resin, you need to wear gloves, the resin will hurt your hands)

Step 5: After finishing the effect of the upper half of the face mold. The same method should be done again for the lower part of the head, and the two sides of the mold should be combined to form a whole head mold.

Step 6: After the mold comes out, it is better to leave it for 24 hours. Spread the release agent evenly on the inside of the mold, clamp the first part of the mold tightly, mix it with platinum silica gel with low viscosity, and pour it into the head mold . It can be heated and cured, and efficiency will be improved. Wait until the solidification is complete before taking it out.

Step 7: Coloring: After successfully finishing, you can start preparing to color the silicone head. The extra part around the silicone can be carefully repaired with a utility knife. The eyes can be dug out with a utility knife to reserve a place for the cosmetic contact lenses. The mouth can be opened as needed. It is also possible to reserve an abrasive tool with an opening in the mouth before injecting silica gel.

Step 8: For the sake of beauty, we need to make hair. The hair can be sewn into a wig, or you can buy a hood and attach it with AB glue. The head of the beautiful finished beauty silicone doll is finished

Next is the production of body parts

Here I will explain in detail the production process of Japanese doll manufacturers:

The first step: find a beautiful model to engrave the model, this process is the business of the engraver, no detailed introduction

The second step: After carving the mold, put the finely carved sludge, flatten the mold, select the mold line, and use the side of the body as the mold line. Make a sled on the sludge (that is, make a raised block). Prevent sliding after closing the mold.

Step 3: Apply release agent on the upper part, apply platinum silica gel with a large viscosity suitable for brushing, and brush three layers. After the glue has solidified, make a layer of FRP outer mold, which can also be made of three layers, and each layer can be put on gauze to increase the tensile and tear resistance. In this way, the upper mold is ready

Step 4: Turn it over and make the lower part of the mold. Similarly, apply the release agent, stir the high-viscosity mold silicone rubber such as Y830, and then use a brush to brush on the mold. Remember, the second part of the sled must be done, and it must be done around the mold line, each with a certain distance.

Step 5: When the lower part of the silicone mold is finished, start to make the resin fiberglass outer mold, the method is the same as before. Brush on three layers. Then the sharding model is ready. Use an electric drill to drill a suitable hole on the edge and punch a screw hole.

The picture below shows the screw holes after clamping the mold.

Step 6: The molds for the upper and lower molds are completed, and the next step is to start the real body. Fix the body mold as shown below

Step 7: Use a hook to hang a skeleton and place it in the body mold. As shown below, of course this is the finished product. Reference only

Step 8: After the skeleton is put in place, stir the 0 degree silica gel according to the proportion, and pour the silica gel from the joint of the neck to completely solidify. Unscrew the screws and remove the silicone body. Repair and remove the edge material of the mold line. 

Step 9: Connect the body and the head together. Finished, the post is the makeup artist's business.

These are just simple steps, the actual production process is more complicated. According to statistics from the sex doll factory, it takes at least ten workers and 80 hours to produce a perfect lifelike sex doll. Therefore, DIY sex doll is indeed a big project. Therefore, it is still a very good way to choose a trusted supplier of sex dolls to buy sex dolls.

If you want to learn more, you can visit www.uusexdoll.com. Professional sex doll factory website.